Product Description
This is the new Arduino Uno R3. In addition to all the features of the previous board, the Uno now uses an ATmega16U2 instead of the 8U2 found on the Uno (or the FTDI found on previous generations). This allows for faster transfer rates and more memory. No drivers needed for Linux or Mac (inf file for Windows is needed and included in the Arduino IDE), and the ability to have the Uno show up as a keyboard, mouse, joystick, etc.
The Uno R3 also adds SDA and SCL pins next to the AREF. In addition, there are two new pins placed near the RESET pin. One is the IOREF that allow the shields to adapt to the voltage provided from the board. The other is a not connected and is reserved for future purposes. The Uno R3 works with all existing shields but can adapt to new shields which use these additional pins.
Arduino is an open-source physical computing platform based on a simple i/o board and a development environment that implements the Processing/Wiring language. Arduino can be used to develop stand-alone interactive objects or can be connected to software on your computer (e.g. Flash, Processing, MaxMSP). The open-source IDE can be downloaded for free (currently for Mac OS X, Windows, and Linux).
Note: The Arduino Uno R3 requires the Arduino 1.0 drivers folder in order to install properly on some computers. We have tested and confirmed that the R3 can be programmed in older versions of the IDE. However, the first time using the R3 on a new computer, you will need to have Arduino 1.0 installed on that machine. If you are interested in reading more about the changes to the IDE, check out the official Arduino 1.0 Release notes!
Features:
- ATmega328 microcontroller
- Input voltage - 7-12V
- 14 Digital I/O Pins (6 PWM outputs)
- 6 Analog Inputs
- 32k Flash Memory
- 16Mhz Clock Speed
Arduino Development Board- $29.99 |
Product Description
The RedBoard - BreadBoard Kit allows you to assemble your very own Uno-compatible development board on a breadboard. If you've ever wanted to make an Arduino-style board from scratch or just understand how it all works, this kit is a good start.
We've put together all the parts you will need including an ATmega328 preloaded with the Uno bootloader. The breadboard overlay makes it easy to hook everything up correctly. Once you are finished, you will have a fully functioning Arduino-compatible controller on a breadboard.
An instruction booklet is included. Previous experience with a breadboard and electronics is recommended but not absolutely necessary.
Note: You will need an FTDI basic for loading code and communicating with the board. Check the related products down below.
Includes:
- Assembly guide
- Clear breadboard
- Jumper wires
- Breadboard overlay
- ATmega328 with Uno bootloader
- All other components necessary to get up and running
RedBoard - Breadboard Kit - $24.99 |
Product Description
Description: Riding on the waves of the very popular Arduino USB board is this small prototyping shield. Originally spawned with collaboration between the folks at SFE and ITP @ NYU, the ProtoShield mates with the Arduino USB board and gives the user a small soldering area, two general LEDs, access to a BlueSMiRF socket, a general pushbutton switch, and most important of all - the Arduino reset switch is brought to the top level.
This comes in kit form and must be soldered together by the end user. Please note - we do not ship assembly instructions, but you can find a big, clean photographed assembly guide here! There are a few tutorials on assembly listed below. All soldering is through-hole (relatively easy) but always check your component orientation before soldering!
The kit is pictured with the bread-board option. We highly recommend this breadboard! See the related items below for all the colorful options of breadboards you have.
Kit Includes:
- 1x ProtoShield bare PCB
- 2x Stackable Headers 6-pin
- 2x Stackable Headers 8-pin
- 2x 5mm Basic Yellow LEDs
- 2x 330 Ohm resistors
- 1x 10k resistor
- 2x Momentary push buttons
- 2x 0.1uF Ceramic Capacitors
Features:
- All Arduino pins are brought to the top level
- 5V, GND, and Vin pins are exposed as well
- BlueSMiRF socket for wireless communication between Arduinos
- 2 general use LEDs
- 1 general use button
- Reset button brought to top level
Protoshield - $14.99 |
Jumper Wires Premium 6" F/F Pack of 10
Product Description
This is a SparkFun exclusive! These are 155mm long jumpers with female connectors on both ends. Use these to jumper from any male header on any board, to any other male header. Combine these with our male to male jumpers to create a male to female jumper. Multiple jumpers can be installed next to one another on a 0.1" header. Comes as 1 package of ten jumpers (colors shown).
Dimensions: 155mm +/-5mm long
Jumper Wires Premium 6" F/F Pack of 10 - $3.49 |
Product Description
These are standard alligator clip to alligator clip cables. Package contains a pair of red and black cables.
Dimensions: 12"
Alligator Cables - $2.49 |
Product Description
What more to say? This is the Raspberry Pi 0. The first $5 dollar single board Linux computer!
Raspberry Pi 0 - $4.99 |
pi2vga Raspberry Pi 0 VGA adapter
Product Description
This is a kit for the pi2vga adapter by Gert. Save yourself the time and get the PCB's and parts all in one place. Pi 0 not included.
Instructions
https://sites.google.com/site/mincepi/pi2vga
pi2vga - $4.99 |
Active Mini HDMI to VGA adapter
Product Description
This Mini HDMI to VGA adapter is the most convenient and cost effective solution for connecting your HDMI devices to your VGA monitors or projectors. Features a built-in active IC chip to achieve better compatibility. This is a great adapter for the Raspberry Pi 0.
Features
- Supports 1080p and 1600x1200 resolutions
- Built-in active IC chip converts digital HDMI signal into analog VGA video
- Plug and play: driver not required
Technical Specification
Active Mini HDMI to VGA adapter- $14.99 |